ATT-0116 | 2 IN 1 SENSOR TAP WITH MANUAL ON/OFF ACTIVATION

Pillar design electronic sensor tap with ON/OFF water control and temperature control lever

ATT-0116

Pillar design electronic sensor tap with ON/OFF water control

Features:
Pillar design sensor tap
Manual ON/OFF water control system
Manual temperature control lever 
Hygienic and up-to 70% water conservation
Independent battery holder: 4XAA Alkaline batteries
Hands free and reliable infrared activation technology
Capacitive touch sensor override control
Solid brass construction
2x flexible supply hoses*Battery-powered only

Water Feed: Double (hot & cold) water supply
Finish: Chrome-plated
Type: Deck-mounted

Power Option
Batteries only (DC6V)

Drilling a hole?
35mm

Water Pressure
0.75bar (Minimum) - 1bar (Recommended).

Buy Product

Lorem Ipsum

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nunc quam urna, dignissim nec auctor in, mattis vitae leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit.

Lorem Ipsum

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nunc quam urna, dignissim nec auctor in, mattis vitae leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit.

Display 5.2"
Camera 12MP
RAM 4GB
OS iOS

Incredible product

John Smith, 20 Jan 2018

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Donec augue nunc, pretium at augue at, convallis pellentesque ipsum. Lorem ipsum dolor sit amet, consectetur adipiscing elit.

Incredible product

John Smith, 20 Jan 2018

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Donec augue nunc, pretium at augue at, convallis pellentesque ipsum. Lorem ipsum dolor sit amet, consectetur adipiscing elit.

Incredible product

John Smith, 20 Jan 2018

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Donec augue nunc, pretium at augue at, convallis pellentesque ipsum. Lorem ipsum dolor sit amet, consectetur adipiscing elit.


Technical Details:
Hottest temperature: 55°C
Coldest temperature: 25°C 
Diameter of 'inlet' flexible hoses: G1/2”
Water pressure range: 0.7 (Min) - 8 Bar (Max)
Voltage: DC6V (*Battery only)
Power consumption: =0.3MW
Sensing distance: 10-31cm
Respond time: 1 Second
Battery Consumption: 4xAA alkaline batteries (up to 2 years lifespan)
Silent Consumption: 0.003W
Environment Temperature: 1-45 C
Flow Rate: 5.7L/Per minute
Pipe Threading: British Standard Whitworth (BSW)

Note:
Gravity-fed water supply users:
You'll need at least 0.75 bar of equal pressure from hot and cold supply in order for this tap to work properly. A pressure pump/booster can be used to increase the water pressure. In summary, the pressure of 'hot' and 'cold' supply feeds must be equal for the temperature control to work efficiently.

This sensor tap can be powered by either Batteries and Mains (AC+DC) *** A transformer is supplied
This sensor tap comes with double water supply feeds





Not applicable


1x Sensor Tap
1x Battery Box
2x Flexible G1/2" *600mm Connection Hoses
Fittings and Screws




Not applicable

IRC-613 REMOTE CONTROL



FLUSH/RUN Water: Flow Time Increase
When this button is pressed once, it will increase water flush/flow time by ‘5 seconds’. Each key press represents 5 seconds ‘flow time’ increment.

HOW TO: 
With remote control facing/pointing towards the sensor, press once, a solid LED light comes on first and briefly followed by 3 LED light flashes. Each key press increases water flow time by 5s. For example, press 1 time =5s, press 2 times= 10s, 3 times= 15s etc.

NOTE: 
Each key press must be registered by sensor module first before setting another parameter. For example, if you want the tap to run for 10 seconds, press this key once and let it register (which equals 5s) and press it again the second time to increase it from 5s to 10s and so on.
FLUSH/RUN Water: Flow Time Decrease
When this button is pressed once, it will decrease water flush/flow time by ‘5 seconds’. Each key press represents 5 seconds ‘flow time’ decrement.

HOW TO: 
With remote control facing/pointing towards the sensor, press once, LED light flashes 3 times. Each key press will decreases water flow time by 5s. For example, press 1 time =-5s, press 2 times= -10s, 3 times= -15s etc.

NOTE: 
Each key press must be registered by sensor module first before setting another parameter. For example, if you want the flow time to be decreased by 10 seconds, press this key once and let it register (which equals -5s) and press it again the second time to decrease it from 10s to 5s and so on.
Increase Sensor Distance
This button will increase the sensor distance by/between 2-5cm.

HOW TO: 
With remote control facing/pointing towards the sensor, press once, a solid LED light comes on first and briefly followed by 3 LED light flashes. Each key press increases sensor proximity zone, and represents 2-5cm increment.

*Sensor distance range scope is around/between 7cm-35cm
Decrease Sensor Distance
This button will decrease the sensor proximity distance by/between 2-5cm.

HOW TO: 
With remote control facing/pointing towards the sensor, press once, a solid LED light comes on first and briefly followed by 2 LED light flashes. Each key press increases sensor proximity zone, and represents 2-5cm increment.

*Sensor distance range scope is around/between 7cm-35cm
Auto Search
This button allows the 'automatic' settings of the sensor proximity sensor range. 

HOW TO: 
With remote control facing/pointing towards the sensor, press once, a solid LED light comes on first and briefly followed by 5 LED light flashes. During these flashes, the sensor will auto-calibrate itself and adjust its infrared distance settings in accordance with environment. 

This button can also be used to set the sensor distance manually.
 
For example, once this button is pressed, place hand/object at desired position/distance where you want sensor range to end and it will automatically calculate the distance from sensor module to hand/object.
Standby
This button will put the sensor on standby or 'inactive' mode. This is particularly useful if the tap needs cleaning or simply trying to put the sensor tap 'out of action' during holiday period. When this mode is active, the sensor will not respond to any interaction with it until it's switched ON again. 

HOW TO: 
With remote control facing/pointing towards the sensor, press once, LED light comes on and stays on for 2-3 seconds and then goes off, standby mode is now active.

To disable, press once, LED light comes on and stays on for 2-3 seconds ‘twice’ and then goes off. Standby mode is now disabled.